Brew Log History
Target 67°F
Ambient: {{ stats.ambient | number:0 }} °F
OG: {{ stats.ogGravity | number:3 }}
Attenuation: {{ stats.attenuation | number:2 }}%
Calories: {{ stats.calories | number:1 }} / 12oz
Carbs: {{ stats.carbs | number:1 }} g / 12oz
Readings: {{ readingsCount | number }}
{{ formatHeaderDate(dates.navStart) | date:'mediumDate' }} to {{ formatHeaderDate(dates.navEnd) | date:'mediumDate' }}
Last Updated: {{ stats.lastupdated.ago }} from {{ stats.lastupdated.source }}
Hops
Amount
|
Variety
|
Cost
|
Type
|
AA
|
Use
|
Time
|
IBU
|
Bill %
|
32 g |
East Kent Goldings32 g East Kent Goldings Hops |
|
Pellet |
5.6 |
Boil
|
60 min |
23.35 |
100% |
32 g
/ $ 0.00
|
Mash Guidelines
Amount
|
Description
|
Type
|
Start Temp
|
Target Temp
|
Time
|
4.5 gal |
Single Infusion |
Infusion |
162 °F |
152 °F |
60 min |
Starting Mash Thickness:
1.5 qt/lb
Starting Grain Temp:
70 °F |
Priming
Method: co2
CO2 Level: 2.2 Volumes |
Target Water Profile
Pittsburgh Tap (7/3/21)
Notes
YEAST STARTER
- 1 Day prior to Brewing, make 10% DME solution in Erlenmeyer Flask.
MFG Date: //__
Starter: __ gm DME / __ L (per MrMalty.com)
- Apply Ice Bath until Temperature reaches ~70F.
- Squeeze 1 packet of WLP002 into DME Solution.
- Cover with Aluminum Foil + apply to Stir Plate for 24 hours.
MASH
PRE-HEAT MASH - 2 gal of Boiling Water
PRE-HEAT SPARGE - 2 gal of Boiling Water
(conduct Simultaneously)
Water Volume: 4.2 gallons for 1.5 lb/qt ratio.
- Prior to heating HLT, check pH of tap water
pH: ______
- STRIKE WATER: 164F.
- Add Grains @ 162F.
- Allow Temperature to fall to 152F prior to closing lid.
- Check Mash pH ~15 minutes into Mash.
pH: ______
- Total Mash Time: 60 minutes
FINAL MASH TEMP: ____F
FINAL MASH pH: ____
- Add 1.5gal of Boiling Water at the end of Mash and stir into solution
- Begin Vorlauf!
SPARGE
- Add 6.5gal of water to Pot. Prior to heating, adjust pH to </= 6.0 with Lactic Acid
Lactic Acid addition: ____ mL
Final pH measurement: ____
- Heat 6.5gal of Water to 175F. Add to Sparge Vessel.
- Recirculate 4 times (or until clear running's) prior to collecting wort.
- Attempt to Sparge over 40 minutes, collect 7.75 gal into boil kettle.
BOIL
- Check Pre-Boil Gravity (goal: 1.042) + pH
NOTE: Make sure to adjust for TEMPERATURE
PRE-BOIL GRAVITY: ____ @ ____F
- Adjust Gravity to Goal (1.042)
Adjusted Gravity: ____ (__ @ __ F)
PRE-BOIL pH: ____
- Adjust Pre-Boil pH to: ~5.5 (+/- 0.1)
Final pH measurement: ____
Lactic Acid addition: ____ mL
- Boil for 90 minutes (goal OG: 1.059)
- Add Kent Golding Hops @ 60 minutes.
- Add Lactose @ 15 minutes.
- Add 1 crushed Whirlfloc tablet @ 5 minutes.
- Chill wort to ~70F after completion of Boil
- Auto-siphon wort from Kettle into Mash Cooler with Hop Cylinder + fine mesh bag attached (at the end of auto-siphon)
- Gravity feed 5.25gal (5gal mark) of wort from Mash Cooler into Catalyst Fermenter
- Allow Ranco/Chest Freezer to adjust wort temperature to goal starting temp
ORIGINAL GRAVITY: ______ (goal: 1.059)
FERMENTATION
- Goal Starting Temp: 67F
- Once signs of Fermentation begin to slow, increase temp by 1F/24hr until 70F. Leave at 70F for the duration of Fermentation
- After diacetyl has cleaned up, cold crash beer to 40F for 2-3 Days prior to transferring to Keg.
carbonate to approximately 1.5-2 volumes CO2
Last Updated and Sharing
- Public: Yup, Shared
- Last Updated: 2021-11-14 14:54 UTC
For quick copying and pasting to a text based forum or email.
Click the Download as HTML file button below.
Recipe costs can be adjusted by changing the batch size. They won't be saved but will give you an idea of costs if your final yield was different.
|
Cost $ |
Cost % |
Fermentables |
$ |
|
Steeping Grains (Extract Only) |
$ |
|
Hops |
$ |
|
Yeast |
$ |
|
Other |
$ |
|
Cost Per Barrel |
$ 0.00 |
|
Cost Per Pint |
$ 0.00 |
|
Total Cost |
$ 0.00 |
|
Discussion about this recipe:
Back To Top