Anyone have a Mark II or bucket blaster or diy auto keg cleaner. Do they work well?

Selling some of my equipment (Complete Clawhammer BIAB System 120V with neoprene blanket, Brewers Edge BIAB system, Mill, Brewtech SS Fermenter, Pump, CO2 tank about 1/2 full, Anvil Fermenter Bucket, Stir plate, 40 plate chiller, etc.). Not looking to break it up, giving a value of $1,500...

I've partly posted bits and pieces in other threads, but for ease of reading, here's the story I brewed beer. Nothing strange there. Fermented and when I figured it was close to finished, I filled a keg (8 litre oxebar) and 1 litre pet bottle. When tasting yesterday, there was a heck of a...

Hi everyone, I've found it a challenge to clean the gunk off the bottom of a spent keg, especially when I want to refill the same keg on the same day I've been using oxy clean with a warm water swirl. However, there's often a bit of gunk on the bottom of the keg nevertheless. My first idea...

Thinking about bottling some Belgian Golden Ale I currently have in the keg fully carbed to compare with future brewings of the same recipe. I've done it before to just take to a party and it gets consumed within a few hours, but if I intend to keep it in the bottle for longer (few weeks to...

I'm currently fermenting ~4 gallons of Golden ale with an OG of 1.047. It's currently at 1.017, it likely has another 5-10 gravity points to go. It's in a corny keg with the PRV removed for gas release. What would happen if I put the PRV back on today? Would the last bit of attenuation cause...

I think that, as a freshman, I was too eager to fill from cornelius keg to bottle (with a beergun) and did not let the pressure build up in the beer for long enough. Does anyone have experience trying to repair too low CO2 by pouring back the beer from the bottle back in the keg? I understand...

G'day brewers, I have 2 kegs in a commercial kegerator (1 beer, 1 soda water). They are fed by 1 gas tank via a tee piece. I don't force carb the beer - I just set and forget it at 10-12 psi. However I force carb the water at 40 psi but when I do this I disconnect the beer gas line. I've...

Hey guys, I was just able to acquire 2 kegs from my brother's father in law. 1 is a pin lock and the other is a ball lock. I'd like to change out the posts so they are the same. Is there any advantage of 1 over the other? Any feedback would be appreciated... Thanks!

G'day brewers, I've got a problem with flat foamy keg beer. It's my first go at kegging and I did a lot of research (thanks YouTube). In short I made a kegerator out of a small fridge. 1 regulator, tee piece, 2 kegs and CO2 tank in the fridge, taps on the door (1 beer, 1 soda water). Here's my...

I have an all grain IPA in primary fermenter now Day 6. Fermentation slowed yesterday. I dry hopped this morning. Planning on dry hopping for 3 days. At that point would you A. Transfer to secondary fermenter for 10 days then Keg OR B. Transfer to Keg for 10 days then chill?

Afternoon everyone, I'm looking at building an electric heated kettle from a 30 L keg and was wondering if anyone could recommend some heating elements, I was thinking of using washing machine ones but read that they might not do the job.i will just be plugging them into a socket 32amp I think...

My last batch of session ale was slightly over pitched with re-hydrated S-04 and spent the first 3 days around 72f. Fermentation took off like a rocket and was at my expected FG (OG1.039-FG1.009) within 72 hours. A comment by another member got me concerned about the acetaldehyde that the warm...