NZ Pils (2) - Beer Recipe - Brewer's Friend

Brewer's Friend

Print

NZ Pils (2)

184 calories 22.1 g 12 oz
Beer Stats
Method: All Grain
Style: German Pils
Boil Time: 60 min
Batch Size: 5 gallons (fermentor volume)
Pre Boil Size: 7 gallons
Pre Boil Gravity: 1.039 (recipe based estimate)
Efficiency: 66% (brew house)
Source: byo
Calories: 184 calories (Per 12oz)
Carbs: 22.1 g (Per 12oz)
Created: Friday December 1st 2017
1.055
1.018
4.9%
34.5
3.9
n/a
n/a
 
Fermentables
Amount Fermentable Cost PPG °L Bill %
11.25 lb American - Pale 2-Row11.25 lb Pale 2-Row 37 1.8 100%
11.25 lbs / 0.00
 
Hops
Amount Variety Cost Type AA Use Time IBU Bill %
0.50 oz Green Bullet0.5 oz Green Bullet Hops Pellet 11 Boil 30 min 17.7 16.7%
1 oz Green Bullet1 oz Green Bullet Hops Pellet 11 Boil 8 min 13.87 33.3%
1.50 oz Green Bullet1.5 oz Green Bullet Hops Pellet 11 Boil 1 min 2.98 50%
3 oz / 0.00
 
Yeast
Wyeast - Pilsen Lager 2007
Amount:
1 Each
Cost:
Attenuation (avg):
73%
Flocculation:
Medium
Optimum Temp:
48 - 56 °F
Starter:
No
Fermentation Temp:
-
Pitch Rate:
0.35 (M cells / ml / ° P) 90 B cells required
0.00 Yeast Pitch Rate and Starter Calculator
 
Target Water Profile
Balanced Profile
Ca+2 Mg+2 Na+ Cl- SO4-2 HCO3-
0 0 0 0 0 0
Mash Chemistry and Brewing Water Calculator
 
Mash Guidelines
Amount Description Type Start Temp Target Temp Time
4 qt Sparge -- 158 °F 60 min
Starting Mash Thickness: 1.3 qt/lb
Quick Water Requirements
Water Gallons  Quarts
Strike water volume at mash thickness of 1.3 qt/lb 3.66 14.6  
Mash volume with grains 4.56 18.2  
Grain absorption losses -1.41 -5.6  
Remaining sparge water volume (equipment estimates 4.61 g | 18.5 qt) 5 20  
Mash Lauter Tun losses -0.25 -1  
Pre boil volume (equipment estimates 6.61 g | 26.5 qt) 7 28  
Boil off losses -1.5 -6  
Hops absorption losses (first wort, boil, aroma) -0.11 -0.5  
Post boil Volume 5 20  
Going into fermentor 5 20  
Total: 8.66 34.6
Equipment Profile Used: System Default
 
Notes

this is a rehash of my NZ Raw Pils (which i did not boil) For this one I will boil the wort as normal and see how good it is. My guess is that in the end it will be about the same but in the beginning it will be more normal than the raw version was (really corney for a month or so)

Axing the DME for all 2row grain this time.

making more grain adjustments to account for volume loss.

will leave hop schedule the same. hop utilization will probably be better but not sure how i can calculate how much and adjust accordingly.....maybe possible though....

Mash as 158 again.

day before brew day i combined some recycled yeast and starter wort at room temp. got a little activity (usually takes longer for recycled yeast).

on brew day I chilled wort down to about 80 and just pitched and added to fermentor (forgetting the wort had to get down to 55 instead of 70) also i forgot that for pilsner ideally you need about twice as many yeast cells to start with (because they multiply less/slower at the lower fermentation temperatue).

so for next time i should start the starter a week or maybe even more ahead of time and end up adding two portions of wort starter (one at a time maybe). also be sure to chill the wort down to 55 before pitching?

here are some pilsner tips from allaboutbeer.com

  1. Ensure that fermentation conditions (48-55 degrees F) can be met and stay well within the temperature boundaries of the yeast.

  2. Chill wort to primary fermentation temperature before pitching yeast.

  3. Maintain good wort aeration to get out of the gate strongly.

  4. Prepare a yeast starter about twice as large as that for top-fermented beers, and optimally refresh that starter on brew day.

  5. Perform a diacetyl rest (65-68 degrees F for 2 days) near the end of primary fermentation.

  6. Lager for a minimum of 6 to 8 weeks, starting at 50 degrees F and dropping gradually over a few days to near freezing.

  7. If bottling, prime with fresh yeast to ensure thorough conditioning.
Last Updated and Sharing
 
300
Views
0
Brews
Recipe QR Code
  • Public: Yup, Shared
  • Last Updated: 2019-06-10 17:13 UTC