Pilsner Urquell National Award-Winning Clone (Decoction and Non-Decoction Version) - Beer Recipe - Brewer's Friend

Brewer's Friend

Print

Pilsner Urquell National Award-Winning Clone (Decoction and Non-Decoction Version)

168 calories 17.6 g 12 oz
Beer Stats
Method: All Grain
Style: Czech Premium Pale Lager
Boil Time: 90 min
Batch Size: 5.5 gallons (fermentor volume)
Pre Boil Size: 7 gallons
Post Boil Size: 6 gallons
Pre Boil Gravity: 1.044 (recipe based estimate)
Post Boil Gravity: 1.051 (recipe based estimate)
Efficiency: 81% (brew house)
Source: Lil' Wheaty's Original
Calories: 168 calories (Per 12oz)
Carbs: 17.6 g (Per 12oz)
Created: Sunday February 26th 2023
Similar Recipes

Pilsner Urquell National Award-Winning Clone (Decoction and Non-Decoction Version)

by Lil' Wheaty's

OG: 1.051 FG: 1.013 ABV: 5.0% IBU: 38

Premium Czech Pilsner

by Tylor Miranda

OG: 1.050 FG: 1.013 ABV: 4.9% IBU: 35

4Gs Pilsner

by 4Gs Brewing

OG: 1.045 FG: 1.007 ABV: 5.0% IBU: 31

1.051
1.013
5.0%
36.0
2.9
n/a
n/a
 
Fermentables
Amount Fermentable Cost PPG °L Bill %
9.17 lb German - Pilsner9.17 lb Pilsner 38 1.6 100%
9.17 lbs / 0.00
 
Hops
Amount Variety Cost Type AA Use Time IBU Bill %
1.38 oz Saaz1.38 oz Saaz Hops Pellet 3.5 Boil 60 min 17.62 27.3%
1.83 oz Saaz1.83 oz Saaz Hops Pellet 3.5 Boil 20 min 14.15 36.2%
0.92 oz Saaz0.92 oz Saaz Hops Pellet 3.5 Boil 10 min 4.26 18.2%
0.92 oz Saaz0.92 oz Saaz Hops Pellet 3.5 Boil 0 min 18.2%
5.05 oz / 0.00
 
Other Ingredients
Amount Name Cost Type Use Time
5.50 ml Lactic acid Water Agt Mash 90 min.
0.46 tsp Irish Moss Fining Boil 15 min.
0.27 ml Lactic acid Water Agt Sparge 30 min.
 
Yeast
Wyeast - Czech Pils 2278
Amount:
0.92 Each
Cost:
Attenuation (avg):
72%
Flocculation:
Med-High
Optimum Temp:
50 - 58 °F
Starter:
Yes
Fermentation Temp:
56 °F
Pitch Rate:
1.5 (M cells / ml / ° P) 394 B cells required
0.00 Yeast Pitch Rate and Starter Calculator
Priming
Method: co2       CO2 Level: 2.25 Volumes
 
Target Water Profile
Balanced Profile
Ca+2 Mg+2 Na+ Cl- SO4-2 HCO3-
100 18 20 45 105 235
Lactic acid added to augment a mash pH of ~ 5.3.
Mash Chemistry and Brewing Water Calculator
 
Mash Guidelines
Amount Description Type Start Temp Target Temp Time
4 gal Protein Rest - Pull the first decoction when finished Temperature -- 125 °F 15 min
4 gal Beta Rest - Add the first decoction back, aiming for a temperature of 148F. Hold this rest for 30min, then pull the second decoction Decoction -- 148 °F 30 min
4 gal Alpha Rest - Add the second decoction back, aiming for a rest temperature of 158F. Hold at this temperature for 30min Decoction -- 158 °F 30 min
4 gal Mash Out - Raise the temperature to 167F and hold for 10min Temperature -- 167 °F 10 min
3.6 gal Sparge - Sparge as usual after mash Temperature -- 170 °F 30 min
Starting Mash Thickness: 1.8 qt/lb
Quick Water Requirements
Water Gallons  Quarts
Strike water volume at mash thickness of 1.8 qt/lb 4.13 16.5  
Mash volume with grains 4.86 19.4  
Grain absorption losses -1.15 -4.6  
Remaining sparge water volume (equipment estimates 5.21 g | 20.8 qt) 4.27 17.1  
Mash Lauter Tun losses -0.25 -1  
Pre boil volume (equipment estimates 7.94 g | 31.8 qt) 7 28  
Boil off losses -2.25 -9  
Hops absorption losses (first wort, boil, aroma) -0.19 -0.8  
Post boil Volume (equipment estimates 5.5 g | 22 qt) 6 24  
WARNING: Exceeded batch size - reduce boil size    
Going into fermentor (equipment estimates 6 g | 24 qt) 5.5 22  
Total: 8.4 33.6
Equipment Profile Used: System Default
 
Notes

Double Decoction:

Note: Pilsner Urquell uses a triple decoction method with an initial acid rest, but I use well enough modified malts and correct for pH already so the first of three decoctions is unnecessary. The decoction measurements below are ones I developed for an electric system and err on the side of caution, so they are the lower amounts needed to potentially reach the next temperature step and direct heat can be applied to compensate.

Perform a protein rest at 125F for 15min, then pull off slightly less than 1/3 (1.16gal/4.4L) of the thickest mash and place it in a separate pot. Bring the pot slowly up to 158F and hold for 15min, then slowly bring it up to a boil and proceed to boil for 10min. Stir often so the grains do not burn, but try to allow some 'browning' to help darken the colour and enhance the flavour/aroma profiles. Add the decoction back to the 125F mash, little by little, aiming for a beta rest temperature of 148F. Hold this temperature for 30min while adding back any leftover decoction (if any) as it cools. After this has finished, pull off roughly 1/6 (0.7gal/2.6L) of the thickest mash a second time and place it in the separate pot. Slowly bring the pot up to a boil and continue to boil for 10min. Add the second decoction back to the mash, little by little, aiming for an alpha rest temperature of 158F. Hold this temperature for 30min while adding back any leftover decoction (if any) as it cools. Once this rest has finished, raise the temperature up to a mash out rest of 167F and hold for 10min. After the decoctions and mash out are finished proceed to sparge/lauter as usual.

No Decoction:

Instead of the labour intensive double decoction mash schedule you could:

  • Substitute some of the pilsner malt for vienna and/or munich to add colour and depth.
  • Include some melanoidin malt for a slight decoction 'feel'.
  • Add some carapils malt (or your preferred alternative) for improved head retention.
  • After which, just carry out a temperature/infusion mash schedule based on your preferences.

    This beer won a national silver medal at the Saskatoon Headhunters Competition (2017) and has consistently scored 40's at other national competitions.

    *With the regular 3.5%AA Saaz the hop additions are 1.5oz @ 90min, 2oz @ 20min, 1oz @ 10min, 1oz @ 0min.


Award Winning Recipe
Last Updated and Sharing
 
419
Views
0
Brews
Recipe QR Code
  • Public: Yup, Shared
  • Last Updated: 2023-02-26 19:17 UTC